ZAVER:

• nejde mi to :D zkoušel jsem to tak 12h
• oficiální initrd rb493g je jen v (23.5/24.10?) nebootuje nejspíš kvůli tomu, že je moc velký - viz post .. haže chybu
• sysupgrade z ar71xx na ath79 asi nejde, protože tomu nerozumí? viz post
• potřeboval bych funkční initrd s ath79 a až z něj flash
• img initrd z buildu 21.02 mi nefunguje
• build z commitu, viz post , mi nejde kvůli zavislostem gcc/g++ což je divný.. mám je :D možná se spíš rozbíji ten script/feed update -a … když jsem na commitu a ne v branch
• zkusit build 19.7, přidat rb435g do ath79 a nový build mi nejde, protože nemám python2 a v tom tree ani není vůbec ještě podpora rb4xx

TODO:

• můžu zkusit tam flashnout oficialni rb493 přes sysupgrade zté 23/24 verze.. ale možná jsem to zkoušel :D
  • nejsem si jistý, zda ten muj build neměl problém s tím umask a jiný jsem možná nezkusil?
  • stačí mi připojit seriovou linku, fallback 19.7 img dát na gw
  • a jeste kabel k rb, abych mohl obnovit konfiguraci
• znovu pročíst stránku zařízení, PR konverzaci, zda mi něco neuniklo :D
• můžu ještě vzít starý systém, centos, a udělat build z commitu, zda to nepůjde?
  • musim pohlidat, ze tam je fakt 4x kernel
• můžu napsat autorovi toho patche, zda to teda má fungovat :D a zda nemá build toho img initrd :D

• Pridat podporu pro 435g podle rb493
  • https://github.com/openwrt/openwrt/commit/b7a8a5454226f34256c5d76480dda5abb1308395
• commity pridavajici 435g do stareho openwrt
  • https://git.openwrt.org/?p=openwrt/openwrt.git;a=commitdiff;h=169e59626805e65022eb757ae0d4e4abf03de5e7
  • https://git.openwrt.org/?p=openwrt/openwrt.git;a=commitdiff;h=d44d954dec6c9c2647a5d66e9d049eeb02367bc7

• https://openwrt.org/toh/mikrotik/rb435
• https://openwrt.org/toh/hwdata/mikrotik/mikrotik_rb435g
• https://openwrt.org/toh/mikrotik/rb493g

• teoreticky by mohl jet i img pro 493G ale muze to delat bordel s eth1, coz ale zase asi nepotrebuji 😄 ale aby to neco neodbouchnulo kvuli GPIO 😄 .. urcite to nezkousej 😄

• Postup
  • obecny,zaklady uzitecny https://openwrt.org/docs/guide-developer/adding_new_device
  • tady o gpio analyze https://openwrt.org/docs/guide-developer/add.new.device#gpios
  • dts https://openwrt.org/docs/guide-developer/defining-firmware-partitions
  • drive bylo v march souborech: https://github.com/openwrt/openwrt/blob/openwrt-19.07/target/linux/ar71xx/files/arch/mips/ath79/mach-rb4xx.c

• diskuze k PR přidání podpory rb493g
  • https://github.com/openwrt/openwrt/pull/3026

• tady nejaky bug s init ramdiskem.. na ktery muzu narazit pri portovani
  • https://github.com/openwrt/openwrt/issues/7591

• tohle taky zajimavy bug
  • https://github.com/openwrt/openwrt/issues/8176

• Nejnižší verze, která mi naběhla, byla 19.07.10 s ar71xx
• nenaběhla mi žádná verze s ath79

• nejspíš kvůli velikosti

» initramfs image will not work if uncompressed image size over ~8.5Mb

• 19.07.10 img má cca 3.9MB
• 24.10 img má kolem 6MB, ale nekomprimovaný má asi 13MB?

binwalk /srv/tftp/openwrt-24.10.1-ath79-mikrotik-mikrotik_routerboard-493g-initramfs-kernel.bin 

DECIMAL       HEXADECIMAL     DESCRIPTION
--------------------------------------------------------------------------------
0             0x0             ELF, 32-bit MSB MIPS-I executable, MIPS, version 1 (SYSV)
9628          0x259C          Copyright string: "Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>"
9836          0x266C          LZMA compressed data, properties: 0x6D, dictionary size: 8388608 bytes, uncompressed size: 13561582 bytes
3948169       0x3C3E89        JBOOT STAG header, image id: 0, timestamp 0x9B1598B1, image size: 275734933 bytes, image JBOOT checksum: 0x31C4, header JBOOT checksum: 0xCFC8

• 23.xx měla taky kolem 12MB
• na diskuzi v PR někdo doporučoval

@flyn-org can you try building an ath79 initramfs image from commit b7a8a54 (this pr), and use that to tftp boot your router and then sysupgrade to your 8/21 image (or something newer)?

I think the „pebs“ issue is exposed when using an ar71xx image to flash an ath79 one.

• a taky

Initramfs doesn't work with image size > ~8.5Mb. LZMA compression has been enabled, as 4.19 kernel buildwill boot, but a 5.4 will not. (open question).

• jenomže neumím udělat build s kernelem 4.19

rb435g

• Můj build 24.10, s umask 0002, s přidanou podporou rb435g

Press any key within 2 seconds to enter setup..␍␊
trying dhcp protocol... OK␍␊
resolved mac address C8:7F:54:53:61:FA␍␊
Gateway: 10.10.11.1␍␊
**transfer started ............................................... transfer ok, time=2.03s␍␊
setting up elf image... OK␍␊
jumping to kernel code␍␊
␊
␍␊
␍OpenWrt kernel loader for AR7XXX/AR9XXX␊
␍Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>␊
␍Decompressing kernel... done!␊
␍Starting kernel at 80060000...␊

• neúspěšný, zastaví se před kernel early print

• nabootoval jsem 19.07 initrd
• přes UI jsem dal upg fw
• UI vypsalo:

Device rb-435g not supported by this image Supported devices: mikrotik,routerboard-435g rb-435g - Image version mismatch: image 1.1, device 1.0. Please wipe config during upgrade (force required) or reinstall. Reason: NAND images switched to yafut. If running older image, reinstall from initramfs. Invalid sysupgrade file. Image check failed.

• dal jsem force a na UART byla chyba, že nenašel kernel

Performing system upgrade...␍␊
Unlocking kernel ...␍␊
Erasing kernel ...␍␊
Writing data to block 0 at offset 0x0␍␊
tar: sysupgrade-routerboard/kernel: not found in archive␍␊
removing ubiblock0_2␍␊
[  278.442383] block ubiblock0_2: released␍␊
Volume ID 1, size 26 LEBs (3301376 bytes, 3.1 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "none", alignment 1␍␊
Volume ID 2, size 27 LEBs (3428352 bytes, 3.2 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs", alignment 1␍␊
Set volume size to 114405376␍␊
Volume ID 3, size 901 LEBs (114405376 bytes, 109.1 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs_data", alignment 1␍␊
sysupgrade successful␍␊

• po rebootu

Press any key within 2 seconds to enter setup..␍␊
␍␊
loading kernel from nand... kernel not found␍␊

• takhle vypadá funkční fw 19.07.10

Performing system upgrade...␍␊
Unlocking kernel ...␍␊
Erasing kernel ...␍␊
Writing data to block 0 at offset 0x0␍␊
Writing data to block 1 at offset 0x20000␍␊
Writing data to block 2 at offset 0x40000␍␊
Writing data to block 3 at offset 0x60000␍␊
Writing data to block 4 at offset 0x80000␍␊
Writing data to block 5 at offset 0xa0000␍␊
Writing data to block 6 at offset 0xc0000␍␊
Writing data to block 7 at offset 0xe0000␍␊
Writing data to block 8 at offset 0x100000␍␊
Writing data to block 9 at offset 0x120000␍␊
Writing data to block 10 at offset 0x140000␍␊
Writing data to block 11 at offset 0x160000␍␊
Writing data to block 12 at offset 0x180000␍␊
Writing data to block 13 at offset 0x1a0000␍␊
removing ubiblock0_2␍␊
[  204.768949] block ubiblock0_2: released␍␊
Volume ID 1, size 14 LEBs (1777664 bytes, 1.6 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "none", alignment 1␍␊
Volume ID 2, size 21 LEBs (2666496 bytes, 2.5 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs", alignment 1␍␊
Set volume size to 116690944␍␊
Volume ID 3, size 919 LEBs (116690944 bytes, 111.2 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs_data", alignment 1␍␊
sysupgrade successful␍␊
umount: can't unmount /dev: Resource busy␍␊
umount: can't unmount /tmp: Resource busy␍␊
umount: ca[  208.451490] reboot: Restarting system␍␊

• myšlenka byla, že bych zkusil sestavit initrd 19.07, která mi funguje, abych ověřil, že to builduji správně
• následně bych tam portoval podporu pro rb435g

• při volání /scripts/feeds update -a mám nesplněné závislosti

Build dependency: Please install Python 2.x

• tak starý python už nemám a ani ho nechci zpětně cpát do systému
• další problém je, že v 19.07 není ještě vůbec mikrotik v ath79, takže by přidání bylo složitější. Musel bych vzít více commitu z 21.02

• kdyz se switchnu na commit b7a8a54, tak to sice kernel 4.19 podporuje, ale nedostanu se ani do menu config, protoze nejde provest ./scripts/feeds update -a
• mám nesplněné závislosti

Build dependency: Please install the GNU C Compiler (gcc) 4.8 or later
Build dependency: Please install the GNU C++ Compiler (g++) 4.8 or later
Build dependency: Please install Python >= 3.5
Build dependency: Please install Python >= 3.5

• přitom mám gcc/g++ i python3
• pak je třeba dát pozor, že se možná musí vybrat kernel ručně. Jsou tam totiž dva (4.19, 5.4)

• jde o nejstarší branch s rb493g v ath79
• preventivně umask viz workaround

umask 0022

git clone https://github.com/openwrt/openwrt.git
mv openwrt openwrt-21.02
cd openwrt-21.02
git checkout openwrt-21.02

./scripts/feeds update -a
./scripts/feeds install -a

$ patch -p1 -b < ../rb435g-24.10.patch
patching file target/linux/ath79/dts/ar7161_mikrotik_routerboard-435g.dts
patching file target/linux/ath79/image/mikrotik.mk
patching file target/linux/ath79/mikrotik/base-files/etc/board.d/02_network
Hunk #1 succeeded at 8 (offset 1 line).
can't find file to patch at input line 98
Perhaps you used the wrong -p or --strip option?
The text leading up to this was:
--------------------------
|diff --git a/target/linux/ath79/mikrotik/base-files/etc/board.d/05_compat-version b/target/linux/ath79/mikrotik/base-files/etc/board.d/05_compat-version
|index 2e079bfa55..d25bf19dfc 100644
|--- a/target/linux/ath79/mikrotik/base-files/etc/board.d/05_compat-version
|+++ b/target/linux/ath79/mikrotik/base-files/etc/board.d/05_compat-version
--------------------------
File to patch:    	
Skip this patch? [y] 
Skipping patch.
1 out of 1 hunk ignored
patching file target/linux/ath79/mikrotik/base-files/lib/upgrade/platform.sh
Hunk #1 succeeded at 31 with fuzz 2 (offset 2 lines).

make menuconfig
make download
make -j24

binwalk bin/targets/ath79/mikrotik/openwrt-ath79-mikrotik-mikrotik_routerboard-435g-initramfs-kernel.bin 

DECIMAL       HEXADECIMAL     DESCRIPTION
--------------------------------------------------------------------------------
0             0x0             ELF, 32-bit MSB MIPS64 executable, MIPS, version 1 (SYSV)
76784         0x12BF0         xz compressed data
76960         0x12CA0         xz compressed data
5151152       0x4E99B0        Flattened device tree, size: 6553 bytes, version: 17

• najde, ale vypisuje jinou chybu než 24.10

setting up elf image... kernel out of range␍␊
kernel loading failed␍␊

• zkusil jsem zmenšit velikost
• odstranil jsem hlavně wifi

ls -lah bin/targets/ath79/mikrotik/openwrt-ath79-mikrotik-mikrotik_routerboard-435g-initramfs-kernel.bin
-rwxr-xr-x 1 djbuldog djbuldog 4,2M 28. dub 00.47 bin/targets/ath79/mikrotik/openwrt-ath79-mikrotik-mikrotik_routerboard-435g-initramfs-kernel.bin

• pak jsem zkusil odstranit úplně maximum včetně SSH, ..
• dostal jsem se na 3.6MB a nic, stejná chyba

• změna targetu na rb493g taky nepomohla
• všiml jsem si, že tam dává už kernel 5.4, což nesplňuje:

Initramfs doesn't work with image size > ~8.5Mb. LZMA compression has been enabled, as 4.19 kernel buildwill boot, but a 5.4 will not. (open question).

• chce to zkusit build s 4.19 kernel z toho commitu?

• https://openwrt.org/docs/guide-developer/toolchain/use-buildsystem
• bacha, zapomněl jsem provést umask 0022 workaround
  • There is an issue affecting the current OpenWrt source tree (from at least 21.02 onwards): OpenWrt images built in certain setups will succeed, but they will hang on boot if installed on a device. To work around this issue, please follow the instructions posted here in the section titled “workaround” before checking out the source tree.

git clone https://github.com/openwrt/openwrt.git
git checkout openwrt-24.10

./scripts/feeds update -a
./scripts/feeds install -a

• aplikoval jsem patch

make menuconfig

• tohle jsou změny v .config vůči default v 24.10

/scripts/diffconfig.sh 
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_mikrotik=y
CONFIG_TARGET_ath79_mikrotik_DEVICE_mikrotik_routerboard-435g=y

• protože nepůjde stahovat instalovat kmod balíčky z repa, rozhodl jsem se nakonec přidat toho více
• vyselektoval jsem hlavně kmod moduly + očekávaný software, který nastavil další připadné kmod závislosti

• stáhl jsem potřebné zdrojové kódy, aby jel paralelní režim rychleji (tip z build guide)

make download

• build na 24 jádrech

make -j 24

• nahrání na tftp server (tftpd-hpa na pharaon)

sudo cp bin/targets/ath79/mikrotik/openwrt-ath79-mikrotik-mikrotik_routerboard-435g-initramfs-kernel.bin /srv/tftp/

• na DHCP jsem nastavil přes UI tftp boot. Musí tam být servername i IP adresa.

• přidal jsem rb435g podle rb493g

cp dts/ar7161_mikrotik_routerboard-493g.dts dts/ar7161_mikrotik_routerboard-435g.dts

• mel by mit jeden WAN a LAN ke switchi AR8316
• v AR7161 jsou 2 MAC rozhrani, ktere potrebuji fyzicka PHY rozhrani.
• vetsinou tam je 1x PHY WAN a 1x switch, jehoz jedno PHY, CPU PHY, je pripojeno k SoC
• komunikace mezi SoC a externim PHY probiha pred MDIO sbernici

• nasledjic vypis ukazuje, ze
  • switch je zaregistrovan na mdio 0
  • port 4 toho switche bude pouzit jako PHY k CPU v SoC
  • SoC, MAC 1, se pripojkil k mdio 0.04 .. tj swtich port 4
  • vytvorilo se z toho eth0 rozhrani.. nema to byt spis eth1? 😄
  • SoC, MAC 0, se pripojilo k mdio 0, port 0?
  • z toho SoC MAC 0 vznikl eth1?

• estli to teda chapu, tak eth0 by mel byt LAN a eht1 wan 😄
• jenomze v openwrt to je obracnee.. eth1 se bere jako lan switch

dmesg
[    3.511322] switch0: Atheros AR8316 rev. 1 switch registered on ag71xx-mdio.0
[    3.861246] ar8316: Using port 4 as PHY
[    4.952016] ag71xx ag71xx.1: connected to PHY at ag71xx-mdio.0:04 [uid=004dd041, driver=Atheros AR8216/AR8236/AR831
6]
[    4.963154] eth0: Atheros AG71xx at 0xba000000, irq 5, mode: rgmii
[    5.301245] ar8316: Using port 4 as PHY
[    5.308704] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd041, driver=Atheros AR8216/AR8236/AR831
6]
[    5.319865] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii

• DTS
  • ja myslim, ze ohledne netwrokingu bych mohl zkusit spis https://github.com/openwrt/openwrt/blob/main/target/linux/ath79/dts/ar7161_ubnt_routerstation-pro.dts
  • s tim, ze eth0 uz je definovano vlastne v https://github.com/openwrt/openwrt/blob/main/target/linux/ath79/dts/ar7100_mikrotik_routerboard-4xx.dtsi

• https://github.com/openwrt/openwrt/blob/openwrt-19.07/target/linux/ar71xx/base-files/etc/board.d/02_network

rb-450g)
		ucidef_set_interfaces_lan_wan "eth1.1" "eth0"
		ucidef_add_switch "switch0" \
			"0@eth1" "1:lan:1" "2:lan:4" "3:lan:3" "4:lan:2"
		;;

• všechny tři ethernetové porty fungují
  • WAN se hlásí jako port0
  • další je port 1
  • další je port 2
  • všechny porty jsou v br-lan a switchují

root@rb435g:~# swconfig dev switch0 show
Global attributes:
	enable_vlan: 1
	ar8xxx_mib_poll_interval: 0
	ar8xxx_mib_type: 0
	enable_mirror_rx: 0
	enable_mirror_tx: 0
	mirror_monitor_port: 0
	mirror_source_port: 0
	arl_table: address resolution table
Port 0: MAC 00:0c:42:bc:07:42
Port 0: MAC b4:8c:9d:35:fb:a9
Port 0: MAC 36:d8:99:91:99:27
Port 0: MAC d8:3a:dd:96:0b:d7
Port 0: MAC c4:82:e1:38:13:5a
Port 2: MAC f0:24:f9:92:b9:64
Port 2: MAC 00:15:6d:c1:c6:9d
Port 2: MAC b8:27:eb:53:27:38
Port 2: MAC c8:7f:54:53:61:fa

Port 0:
	mib: ???
	pvid: 0
	link: port:0 link:up speed:1000baseT full-duplex txflow rxflow 
Port 1:
	mib: ???
	pvid: 1
	link: port:1 link:down
Port 2:
	mib: ???
	pvid: 1
	link: port:2 link:up speed:1000baseT full-duplex auto
Port 3:
	mib: ???
	pvid: 0
	link: port:3 link:down
Port 4:
	mib: ???
	pvid: 0
	link: port:4 link:down
VLAN 1:
	vid: 1
	ports: 0t 1 2

• Zajímavý je, ze ten port 0 má pořád linku nahoře, i když tam není kabel. Možná tím napojením na CPU?
• Takhle to vypadá, když je kabel v portu 3 (LAN2). Eth0 (WAN] nema LOWER_UP a eth1 ano

root@rb435g:~# ip link show | grep eth[01]
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel master br-lan state DOWN qlen 1000
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP qlen 1000
7: eth1.1@eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master br-lan state UP qlen 1000

• Takhle to vypadá při přepojení do WAN

ip link show | grep eth[01]
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel master br-lan state UP qlen 1000
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP qlen 1000
7: eth1.1@eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master br-lan state UP qlen 1000

• Zajímavý je, že v dmesg vidím link up a down, ale jen pro eth0 .. ne pro eth1

• provedl jsem zálohu cfg
• takhle vypadal funkční dmesg v 19.07 (pro srovnání s 24.10)

[    0.000000] Linux version 4.14.275 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11427-9ce6aa9d8d)) #0 Sat Apr 16 13:13:32 2022
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR7161 rev 2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 10000000 @ 00000000 (usable)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 10000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] On node 0 totalpages: 65536
[    0.000000] free_area_init_node: node 0, pgdat 8052bf60, node_mem_map 81000020
[    0.000000]   Normal zone: 512 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 65536 pages, LIFO batch:15
[    0.000000] random: get_random_bytes called from 0x8052d740 with crng_init=0
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: parts=1 boot_part_size=4194304 gpio=4023 HZ=340000000 mem=256M kmac=00:0C:42:BC:07:42 board=435G ver=3.24 hw_opt=00000004 boot=1 mlc=9 console=ttyS0,115200 rootfstype=squashfs noinitrd
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 254116K/262144K available (4209K kernel code, 172K rwdata, 524K rodata, 204K init, 213K bss, 8028K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] Clocks: CPU:680.000MHz, DDR:340.000MHz, AHB:170.000MHz, Ref:40.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5621354254 ns
[    0.000009] sched_clock: 32 bits at 340MHz, resolution 2ns, wraps every 6316128254ns
[    0.007823] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[    0.074085] pid_max: default: 32768 minimum: 301
[    0.078907] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.085514] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.094762] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.104630] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.111797] NET: Registered protocol family 16
[    0.117669] MIPS: machine is MikroTik RouterBOARD 435G
[    0.896283] registering PCI controller with io_map_base unset
[    2.572896] random: fast init done
[    2.812771] rb4xx-spi rb4xx-spi: controller is unqueued, this is deprecated
[    2.820676] PCI host bridge to bus 0000:00
[    2.824780] pci_bus 0000:00: root bus resource [mem 0x10000000-0x16ffffff]
[    2.831681] pci_bus 0000:00: root bus resource [io  0x0000]
[    2.837241] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    2.844024] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    2.851997] pci 0000:00:14.0: [168c:0029] type 00 class 0x028000
[    2.852034] pci 0000:00:14.0: reg 0x10: [mem 0x00000000-0x0000ffff]
[    2.852103] pci 0000:00:14.0: PME# supported from D0 D3hot
[    2.852280] pci 0000:00:17.0: [168c:0029] type 00 class 0x028000
[    2.852306] pci 0000:00:17.0: reg 0x10: [mem 0x00000000-0x0000ffff]
[    2.852365] pci 0000:00:17.0: PME# supported from D0 D3hot
[    2.852512] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    2.852538] pci 0000:00:14.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
[    2.859360] pci 0000:00:17.0: BAR 0: assigned [mem 0x10010000-0x1001ffff]
[    2.869886] clocksource: Switched to clocksource MIPS
[    2.875900] NET: Registered protocol family 2
[    2.880517] IP idents hash table entries: 4096 (order: 3, 32768 bytes)
[    2.887865] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    2.894904] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    2.901291] TCP: Hash tables configured (established 2048 bind 2048)
[    2.907774] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    2.913660] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    2.920125] NET: Registered protocol family 1
[    2.924518] PCI: CLS 0 bytes, default 32
[    2.927221] Crashlog allocated RAM at address 0x3f00000
[    2.933675] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[    2.944742] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.950613] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    2.969400] io scheduler noop registered
[    2.973373] io scheduler deadline registered (default)
[    2.978891] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    2.987238] console [ttyS0] disabled
[    3.010899] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 10625000) is a 16550A
[    3.019599] console [ttyS0] enabled
[    3.026567] bootconsole [early0] disabled
[    3.035665] m25p80 spi0.0: pm25lv512 (64 Kbytes)
[    3.045434] Creating 4 MTD partitions on "spi0.0":
[    3.050279] 0x000000000000-0x00000000b000 : "routerboot"
[    3.057123] 0x00000000b000-0x00000000c000 : "hard_config"
[    3.063849] 0x00000000d000-0x00000000f000 : "bios"
[    3.070577] 0x00000000f000-0x000000010000 : "soft_config"
[    3.077412] NAND flash driver for RouterBoard 4xx series version 0.2.0
[    3.084245] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
[    3.090600] nand: Samsung NAND 128MiB 3,3V 8-bit
[    3.095205] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    3.102784] Scanning device for bad blocks
[    3.168444] Bad eraseblock 207 at 0x0000019e0000
[    3.179969] Bad eraseblock 231 at 0x000001ce0000
[    3.184716] Bad eraseblock 232 at 0x000001d00000
[    3.191825] Bad eraseblock 241 at 0x000001e20000
[    3.224085] Bad eraseblock 336 at 0x000002a00000
[    3.229124] Bad eraseblock 338 at 0x000002a40000
[    3.234477] Bad eraseblock 341 at 0x000002aa0000
[    3.266447] Bad eraseblock 435 at 0x000003660000
[    3.272681] Bad eraseblock 441 at 0x000003720000
[    3.284758] Bad eraseblock 467 at 0x000003a60000
[    3.303563] Bad eraseblock 516 at 0x000004080000
[    3.329674] Bad eraseblock 590 at 0x0000049c0000
[    3.344395] Bad eraseblock 625 at 0x000004e20000
[    3.363788] Bad eraseblock 676 at 0x000005480000
[    3.432043] Bad eraseblock 894 at 0x000006fc0000
[    3.454641] Bad eraseblock 956 at 0x000007780000
[    3.479307] Creating 3 MTD partitions on "NAND 128MiB 3,3V 8-bit":
[    3.485538] 0x000000000000-0x000000040000 : "booter"
[    3.492047] 0x000000040000-0x000000400000 : "kernel"
[    3.498303] 0x000000400000-0x000008000000 : "ubi"
[    3.511322] switch0: Atheros AR8316 rev. 1 switch registered on ag71xx-mdio.0
[    3.861246] ar8316: Using port 4 as PHY
[    4.952016] ag71xx ag71xx.1: connected to PHY at ag71xx-mdio.0:04 [uid=004dd041, driver=Atheros AR8216/AR8236/AR8316]
[    4.963154] eth0: Atheros AG71xx at 0xba000000, irq 5, mode: rgmii
[    5.301245] ar8316: Using port 4 as PHY
[    5.308704] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd041, driver=Atheros AR8216/AR8236/AR8316]
[    5.319865] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
[    5.331810] MikroTik RouterBOARD hardware configuration sysfs driver v0.03
[    5.339592] NET: Registered protocol family 10
[    5.348423] Segment Routing with IPv6
[    5.352237] NET: Registered protocol family 17
[    5.356722] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    5.369672] 8021q: 802.1Q VLAN Support v1.8
[    5.377495] UBI: auto-attach mtd6
[    5.380891] ubi0: attaching mtd6
[    6.197200] ubi0: scanning is finished
[    6.259782] ubi0: attached mtd6 (name "ubi", size 124 MiB)
[    6.265326] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    6.272199] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    6.278966] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    6.285922] ubi0: good PEBs: 976, bad PEBs: 16, corrupted PEBs: 0
[    6.292010] ubi0: user volume: 4, internal volumes: 1, max. volumes count: 128
[    6.299213] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1479584234
[    6.308331] ubi0: available PEBs: 0, total reserved PEBs: 976, PEBs reserved for bad PEB handling: 4
[    6.317568] ubi0: background thread "ubi_bgt0d" started, PID 357
[    6.325252] block ubiblock0_2: created from ubi0:2(rootfs)
[    6.330802] ubiblock: device ubiblock0_2 (rootfs) set to be root filesystem
[    6.354222] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    6.362278] Freeing unused kernel memory: 204K
[    6.366713] This architecture does not have kernel memory protection.
[    7.387959] init: Console is alive
[    7.391764] init: - watchdog -
[    9.000106] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    9.057163] usbcore: registered new interface driver usbfs
[    9.062784] usbcore: registered new interface driver hub
[    9.068153] usbcore: registered new device driver usb
[    9.077994] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    9.086070] ehci-platform: EHCI generic platform driver
[    9.091441] ehci-platform ehci-platform: EHCI Host Controller
[    9.097219] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    9.105268] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    9.139916] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    9.146933] hub 1-0:1.0: USB hub found
[    9.151071] hub 1-0:1.0: 2 ports detected
[    9.157833] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    9.165465] ohci-platform: OHCI generic platform driver
[    9.170860] ohci-platform ohci-platform: Generic Platform OHCI controller
[    9.177660] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
[    9.185682] ohci-platform ohci-platform: irq 14, io mem 0x1c000000
[    9.264623] hub 2-0:1.0: USB hub found
[    9.268695] hub 2-0:1.0: 2 ports detected
[    9.273900] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    9.291638] init: - preinit -
[   10.126616] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   11.150280] ar71xx: pll_reg 0xb8050010: 0x110000
[   11.150295] eth1: link up (1000Mbps/Full duplex)
[   11.154952] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   13.335260] random: procd: uninitialized urandom read (4 bytes read)
[   13.347712] UBIFS (ubi0:3): background thread "ubifs_bgt0_3" started, PID 431
[   13.665211] UBIFS (ubi0:3): recovery needed
[   14.205790] UBIFS (ubi0:3): recovery completed
[   14.210361] UBIFS (ubi0:3): UBIFS: mounted UBI device 0, volume 3, name "rootfs_data"
[   14.218176] UBIFS (ubi0:3): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   14.228098] UBIFS (ubi0:3): FS size: 115294208 bytes (109 MiB, 908 LEBs), journal size 5713920 bytes (5 MiB, 45 LEBs)
[   14.238692] UBIFS (ubi0:3): reserved for root: 4952683 bytes (4836 KiB)
[   14.245311] UBIFS (ubi0:3): media format: w4/r0 (latest is w5/r0), UUID 43EC860C-4076-4F05-B369-14D7CBCE3CE3, small LPT model
[   14.266483] mount_root: switching to ubifs overlay
[   14.310172] urandom-seed: Seeding with /etc/urandom.seed
[   14.546165] eth1: link down
[   14.564538] procd: - early -
[   14.567522] procd: - watchdog -
[   15.202408] procd: - watchdog -
[   15.205866] procd: - ubus -
[   15.347123] random: ubusd: uninitialized urandom read (4 bytes read)
[   15.358073] random: ubusd: uninitialized urandom read (4 bytes read)
[   15.364945] random: ubusd: uninitialized urandom read (4 bytes read)
[   15.372294] procd: - init -
[   16.085541] kmodloader: loading kernel modules from /etc/modules.d/*
[   16.195460] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   16.218943] Loading modules backported from Linux version v4.19.237-0-ga6e4a1818efa
[   16.226655] Backport generated by backports.git v4.19.237-1-0-gffb89fd9
[   16.262111] ip_tables: (C) 2000-2006 Netfilter Core Team
[   16.275590] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
[   16.402878] xt_time: kernel timezone is -0000
[   16.502269] PPP generic driver version 2.4.2
[   16.510963] NET: Registered protocol family 24
[   16.553691] urngd: v1.0.2 started.
[   16.572124] pci 0000:00:14.0: using irq 42 for pin 1
[   16.577104] PCI: Enabling device 0000:00:14.0 (0000 -> 0002)
[   18.141003] ath: EEPROM regdomain: 0x0
[   18.141010] ath: EEPROM indicates default country code should be used
[   18.141013] ath: doing EEPROM country->regdmn map search
[   18.141026] ath: country maps to regdmn code: 0x3a
[   18.141030] ath: Country alpha2 being used: US
[   18.141034] ath: Regpair used: 0x3a
[   18.161753] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   18.163599] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=42
[   18.170394] pci 0000:00:17.0: using irq 42 for pin 1
[   18.175366] PCI: Enabling device 0000:00:17.0 (0000 -> 0002)
[   19.739262] ath: EEPROM regdomain: 0x0
[   19.739270] ath: EEPROM indicates default country code should be used
[   19.739273] ath: doing EEPROM country->regdmn map search
[   19.739286] ath: country maps to regdmn code: 0x3a
[   19.739291] ath: Country alpha2 being used: US
[   19.739294] ath: Regpair used: 0x3a
[   19.760084] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[   19.761934] ieee80211 phy1: Atheros AR9280 Rev:2 mem=0xb0010000, irq=42
[   20.135887] random: crng init done
[   20.139302] random: 6 urandom warning(s) missed due to ratelimiting
[   22.156013] kmodloader: done loading kernel modules from /etc/modules.d/*
[   31.703301] br-lan: port 1(eth0) entered blocking state
[   31.708533] br-lan: port 1(eth0) entered disabled state
[   31.714099] device eth0 entered promiscuous mode
[   31.741472] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   31.998555] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   32.020316] br-lan: port 2(eth1.1) entered blocking state
[   32.025723] br-lan: port 2(eth1.1) entered disabled state
[   32.031482] device eth1.1 entered promiscuous mode
[   32.036271] device eth1 entered promiscuous mode
[   33.070374] ar71xx: pll_reg 0xb8050010: 0x110000
[   33.075000] eth1: link up (1000Mbps/Full duplex)
[   33.079651] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   33.132174] br-lan: port 2(eth1.1) entered blocking state
[   33.137578] br-lan: port 2(eth1.1) entered forwarding state
[   33.184374] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   33.415232] ath: EEPROM regdomain: 0x80cb
[   33.419243] ath: EEPROM indicates we should expect a country code
[   33.425381] ath: doing EEPROM country->regdmn map search
[   33.430692] ath: country maps to regdmn code: 0x37
[   33.435468] ath: Country alpha2 being used: CZ
[   33.439912] ath: Regpair used: 0x37
[   33.443392] ath: regdomain 0x80cb dynamically updated by user
[   33.449284] ath: EEPROM regdomain: 0x80cb
[   33.453295] ath: EEPROM indicates we should expect a country code
[   33.459374] ath: doing EEPROM country->regdmn map search
[   33.464686] ath: country maps to regdmn code: 0x37
[   33.469461] ath: Country alpha2 being used: CZ
[   33.473907] ath: Regpair used: 0x37
[   33.477385] ath: regdomain 0x80cb dynamically updated by user
[   34.832395] ar71xx: pll_reg 0xb8050014: 0x110000
[   34.837019] eth0: link up (1000Mbps/Full duplex)
[   34.861343] br-lan: port 1(eth0) entered blocking state
[   34.866574] br-lan: port 1(eth0) entered forwarding state
[   35.491930] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   35.502188] br-lan: port 3(wlan0) entered blocking state
[   35.507506] br-lan: port 3(wlan0) entered disabled state
[   35.513182] device wlan0 entered promiscuous mode
[   35.517991] br-lan: port 3(wlan0) entered blocking state
[   35.523374] br-lan: port 3(wlan0) entered forwarding state
[   35.870097] br-lan: port 3(wlan0) entered disabled state
[   35.951802] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   35.958373] br-lan: port 3(wlan0) entered blocking state
[   35.963731] br-lan: port 3(wlan0) entered forwarding state